Securing a load in a van rarely works with just one aid. A strap on its own will not reliably hold a smooth crate, a mat on its own will not stop tipping, and without edge protection the strap can be damaged on sharp edges. Only the combination of lashing strap, anti-slip mat and edge protection adds up to a sound securing method. This guide shows how the components work together. You will find suitable equipment in the load securing category. This article is a selection guide – the manufacturer's operating instructions apply for use and inspection.
Why loads slide in a van
When braking, cornering or swerving, forces act on the load that try to set it in motion. In a van, the load floor is often smooth and the load rarely fills the whole area. Gaps remain between crates, cartons and walls, giving the goods room to gather speed.
Good securing therefore works on three points: the load should be positioned as form-fittingly as possible, resting against the front wall or other parts of the load. Friction between load and floor should be high. And straps should hold the load so that it neither slides nor tips. The VDI 2700 guideline series describes the basics of load securing in road transport; for the individual aids, the manufacturer's data applies.

The components at a glance
The following products are made by Dolezych. The values are taken from the manufacturer's data.
- Lashing strap for airline rails: Many panel vans have lashing rails on the wall or floor. The DoZurr 1000 with pressure ratchet + single-stud fitting, 3.50 m is a two-part strap whose single-stud fitting locks directly into the rail. According to the manufacturer: webbing width 25 mm, lashing capacity (LC) 500 daN, standard tension force (STF) 180 daN, elongation below 5%, fixed end 300 mm, loose end 3,200 mm, material PES, standard EN 12195-2.
- Lashing strap for the dropside: On dropside vehicles there are often no lashing points in the right place. The DoZurr 500 with pressure ratchet + dropside clamp, 3.50 m is attached to the dropside with clamps. According to the product data: webbing width 50 mm, fixed end 250 mm, loose end 3,250 mm, permissible tensile force 250 daN, elongation below 5%, standard EN 12195-2.
- Anti-slip mat: The DoMatt anti-slip mats in 4 mm thickness 1250 x 1250 mm increase friction between the load and the load floor. The manufacturer states a coefficient of friction of 0.6 and the standard VDI 2700, sheet 14+15.
- Edge protection: The edge protection bracket for 50 mm belts in orange polypropylene has leg lengths of 185 x 145 mm and, according to the manufacturer, a deflection factor k of 1.8. It has no threading slot and is quick to fit and remove.
- Complete set: The Allround load securing set combines various straps with edge protection corners and anti-slip mats; more on that in the next section.
What the Allround set contains
If you regularly carry different loads, you need more than one type of strap. According to the manufacturer, the set contains:
- 2 × DoZurr 250, 25 mm, one-piece with strap clamp, 4 m
- 2 × DoZurr 700, 25 mm, one-piece with pressure ratchet, 4 m
- 2 × DoZurr 700, 25 mm, with pressure ratchet and profile hook, 4 m
- 2 × DoZurr 2000, 35 mm, one-piece with pressure ratchet, 6 m
- 2 × DoZurr 2000, 35 mm, with pressure ratchet and profile hook, 6 m
- 4 × DoZurr 5000, 50 mm, with pressure ratchet and profile hook, 8 m
- 4 edge protection corners for 50 mm straps
- 8 anti-slip mats, 180 x 120 x 8 mm
The small mats work well under individual crates or pallets, the large sheets under loads that cover a wider area.
How to combine strap, mat and edge protection
- Prepare the load floor: The surface should be clean and dry, as dirt and moisture reduce the effect of the mat.
- Lay the mat: Place the anti-slip mat so that the load stands fully on it and does not overhang the edge.
- Load form-fittingly: Put heavy items at the front against the bulkhead and fill gaps where possible.
- Protect edges: Fit edge protection brackets on sharp edges before tensioning the strap.
- Apply and tension straps: Use the vehicle's lashing points or rails and operate the ratchet until the strap sits tight.
- Re-check: Check the tension again after a short drive and after partial unloading.
Application examples
Pallets and cartons in a panel van
A single pallet stands in the middle of the cargo area with cartons stacked on it. An anti-slip mat goes under the pallet and the load is lashed down with straps attached to the airline rails. Where the strap runs over carton edges, an edge protection bracket spreads the pressure and protects both strap and carton.
Workshop material on the way to the site
Toolboxes, bundles of pipe and machines come in different shapes and weights. A set with several strap sizes helps here. Light items are secured with narrow straps, heavy machines with wider straps and a mat underneath. Sharp metal edges get edge protection.
Dropside van with side boards
On an open dropside body there are often no suitable lashing points. Straps with a dropside clamp can be hooked onto the side board. An anti-slip mat under the load is particularly important here, because wooden floors can become slippery when wet.
Frequently asked questions
Is an anti-slip mat enough without a strap?
As a rule, no. The mat increases friction but does not stop the load from tipping or bouncing over uneven ground. It complements straps rather than replacing them.
How do I know how much a strap may hold?
The manufacturer gives the ratings of the straps, such as the lashing capacity (LC), in the product data. How a strap is marked and when it must no longer be used is set out in the manufacturer's operating instructions. Check the strap before every use.
When do I need edge protection?
Whenever the strap runs over sharp or hard edges, for example on metal parts, crates or stacked cartons. Edge protection keeps the strap from being damaged and the goods from being dented.
Your route to the right equipment
Think about what you carry most often and which lashing options your vehicle offers. For panel vans with rails, straps with a single-stud fitting are a good fit; for dropside vehicles, straps with a dropside clamp. Add anti-slip mats and edge protection, or start with a set. Check straps, ratchets and fittings for damage before every use.
You will find the full range under load securing. If you have questions, call us on +49 2237 628095-00, Monday to Friday from 9 am to 5 pm. The manufacturer's operating instructions always apply for use and inspection.